Used in locations where visibility is limited, the P-270 LED-enhanced pedestrian crossing sign helps
improve pedestrian safety at crosswalk by increasing driver awareness of the sign . The LED-embedded
pictogram is programmed to flash continuously for a set period of time during specific period of
the day when pedestrian security is at stake. An embedded photocell adjusts the intensity of the LED display
according to the ambient light, day or night.
AND THIN DESIGN
ON STANDARD POSTS
DRY CONTACT ACTIVATION
The controller is equipped with a dry contact input for connection of any external sensor.
Sensors could be: pedestrian or motion detector, temperature sensor, speed radar, etc.
When the sensor activates the dry contact, the flasher turns on and runs according to actual setup.
Every event is recorded in the controller. This means it is possible to know the flasher’s status
in any previous time period and to extract data about frequency of use.
Data is exported in CSV format.
EASY PAIRING OF WIRELESS DEVICES
Whether pairing a remote control or two flashers together, the procedure is quick and easy.
Piano switches mounted on the controller allows for devices to create links between eachother
without the need of a computer. Pairing can thus be done on the field, at installation.
Every controller is equipped with an internal schedule that can start or stop the system according
to desired date and time. While in standby, pressing the push-button can still activate the system,
which is great for school zones situations.
To facilitate the flasher setup as much as possible, flashing modes and operation modes are already
programmed in the controller. Piano switches are mounted directly on the controller which makes setup
fast and simple, whether it be at the factory or at installation.
LED CROSSWALK TRAFFIC SIGN TECHNICAL SPECIFICATIONS
OPTIONS : ACTIVATION
WIRELESS PUSH BUTTON
WIRELESS PUSH BUTTON ON SHORT POST
CABLED PUSH BUTTON
PEDESTRIAN SENSOR (2 DAYS AUTONOMY)
OPTIONS : POWER
10W SOLAR PANEL (3 DAYS AUTONOMY)
20W SOLAR PANEL (6 DAYS AUTONOMY)
120V TO 12V POWER CONVERTER, IP67 WITH BATTERY
120V TO 12V
OPTIONS : ACCESSORIES
P-270 FOR 2in
SOLAR PANEL ADAPTER
FOR TELESPAR 2″
WIRELESS COMMUNICATION KEY
ADDITIONAL CABLE FOR 2ND FLASHER
#37079 : Right crosswalk
#37090 : Left crosswalk
#37092 : Right school
#37095 : Left school
Housing: Polyethylene (HDPE) UV protection
Sign face: Acrylic 5 mm (.188 ”)
Reflective sheet: White, High Intensity, Type III
Environmental Protection: IP54
Weight: 20 lb (9 kg)
Box : 914 x 610 x 102 mm (36 x 24 x 6″)
Weight : 22 lb (10 kg)
300 cycles of 30 sec./jour
10 W 3 days autonomy w/o sunlight
20 W 6 days autonomy w/o sunlight
Includes hardware for
2.375’’ + round signposts
Dry Contact Activation: One (1) input available, 9 to 36 VDC
Data Recording: Up to 25 000 events : On, Off, Battery Charge Level,Failures, Faulty LEDs
Wireless Pairing: with controller
Setup: with controller
Schedule: Daily, Weekly and Yearly Program
LED type: 5 mm (T-1 3/4)
Color: Cool White (8000K)
Visibility: more than 300 m (1000’)
Power Pedestrian: 8,7 Wh (day) – 3,1 Wh (night)
Power Schoolboy: 13,5 Wh (day) – 4,6 Wh (night)
Night Dimmer: Built-in (Control Box)
Voltage In: 10.8 to 15 VDC
Voltage Out: 10.8 to 15 VDC
Dry Contact: 9 to 36 VDC
Connector: Snap-in, Overmolded IP67, 10 mm OD
Flashing Type: 0,1 – 0,2 – 0,5 sec. or Tri-flash, 60x per min.
Operation: Push-button or Wireless activation
Wireless Communication: 9 to 36 VDC
Wireless Range: Up to 100 m (330’) free field
Pairing: Built-in (Control Box), PC
Flashing Duration: 30 or 45 s under Controller settings (from 1 to 5000 s under PC settings)
Operational Temperature: -40 to +50°C (-40 to +131°F)
Pre-setup: 0,2 sec. for 30 seconds
Two (2) years limited warranty on defects
for parts and labor/div>